NE555 IC Timer

The 555 Timer is an integrated circuit (chip) implementing a variety of timer and multivibrator applications. The IC was designed and invented by Hans R. Camenzind. It was designed in 1970 and introduced in 1971 by Signetics (later acquired by Philips). The original name was the SE555/NE555 and was called "The IC Time Machine".

The 555 gets its name from the three 5-k Ohm resistors used in typical early implementations. It is still in wide use, thanks to its ease of use, low price and good stability. As of 2003[update], 1 billion units are manufactured every year.

The 555 timer is one of the most popular and versatile integrated circuits ever produced. It includes 23 transistors, 2 diodes and 16 resistors on a silicon chip installed in an 8-pin mini dual-in-line package (DIP-8).

The 555 has three operating modes:

* Monostable mode: in this mode, the 555 functions as a "one-shot". Applications include timers, missing pulse detection, bouncefree switches, touch switches, Frequency Divider,Capacitance Measurement, Pulse Width Modulation (PWM) etc

* Astable - Free Running mode: the 555 can operate as an oscillator. Uses include LED and lamp flashers, pulse generation, logic clocks, tone generation, security alarms, pulse position modulation, etc.

* Bistable mode or Schmitt trigger: the 555 can operate as a flip-flop, if the DIS pin is not connected and no capacitor is used. Uses include bouncefree latched switches, etc.

The connection of the pins is as follows:

Nr. Name Purpose

1 GND Ground, low level (0V)

2 TR A short pulse high → low on the trigger starts the timer

3 Q During a timing interval, the output stays at +VCC

4 R A timing interval can be interrupted by applying a reset pulse to low (0V)

5 CV Control voltage allows access to the internal voltage divider (2/3 VCC)

6 THR The threshold at which the interval ends (it ends if U.thr → 2/3 VCC)

7 DIS Connected to a capacitor whose discharge time will influence the timing interval

8 V+, VCC The positive supply voltage which must be between 3 and 15 V

In the astable mode, the high time from each pulse is given by

high = 0.693.(R1 + R2).C

and the low time from each pulse is given by

low = 0.693.R2.C

where R1 and R2 are the values of the resistors in ohms and C is the value of the capacitor in farads.

Specifications

These specifications apply to the NE555. Other 555 timers can have better specifications depending on the grade (military, medical, etc).

* Supply voltage (VCC) 4.5 to 15 V

* Supply current (VCC = +5 V) 3 to 6 mA

* Supply current (VCC = +15 V) 10 to 15 mA

* Output current (maximum) 200 mA

* Power dissipation 600 mW

* Operating temperature 0 to 70 °C

Read More

Speed Fan Control Circuit using IC CD4017B

Speed Fan Control Circuit using IC CD4017B Circuit

The simple abstraction activity is use IC CD4017 to ascendancy 4 relays which affix anniversary pole. IC CD4017B which is counter-cum-1kHz decoder and the arresting is disconnected into ten according intervals, Which can be programmed, via the distinct location, 10-mode.

According to the backward advertisement of the continuance of the acting period, the agnate achievement of the CD4017 inhibits adverse CD4017 (per pole of circling and diode D6), and fires the triac.

Here transistor T2 acts as a disciplinarian transistor. Pin by 4017, with aught at the achievement of the sensor for the about-face to 0(zero ascertain output) anniversary canyon through zero.

Remark. The accepted beachcomber forms of assertive positions of the rotary switch, as declared in EFY Lab are in the account 1.

The ambit is able to administer for a ambassador in the activity lighting equipment, hot air, oven singal Universal AC motor, heating, etc.

Read More

IC Amplifier with HA13118 Diagram

IC amplifier 18 watt circuit is an IC digit HA13118 Hitachi powerfully. with the intention of the IC yearn for take place integrated amplifiers, categorize AB. And this cycle is to assistance a association circuit. to the same degree a answer, growth toll up to 55 dB. And pressure from 8-18 volt the current 1-2 amps, with not as much of than 0.2% distortion by 1W. And response. frequencies from 30 Hz-30 kHz.

IC Amplifier with HA13118 Circuit Diagram

As entering the power supply circuit, and paid into the audio input. The audio is through VR1 adjusts the level of the audio sign. And pass the C1 coupling signal. The C2 eliminate the interference. From the audio signal to come to pass sent through to the input pin on pin 3 of IC1. so as to this circuit to circuit modish the form of conduit circuits otherwise expansion of the not here navigation. And restore channels laid back, to follow a elevated watt power. The observations from the pin 15 which is the output of absent channel speakers are connected to individual fringe. And the other side of the speakers are connected to the output of pin 8, which is the output of the right. The C7 and C8 acting reaction hint to the circuit’s frequency response is better. The C9, C10, R1 and R2 willpower wait on unconcerned the campaign. And C11, C12 serve to filter the light as it should be to prevent several din shock.

Read More

L200 IC Circuit 3 to 30V Power Supply

 The following picture shown a 3 to 30V power supply circuit diagram using L200 IC made by Anwar von Sroka.It is constructed for the use with 100W transceivers.

The L200 IC which is known as virtually blow-out proof IC for voltage and current programmable regulation, is able for regulating the voltage as well as the current. It should be connected as close as possible to the minus terminal. Here, if you need to see the L200 datasheet.

Download this application datasheet about 3 to 30V Power Supply using L200 IC Circuit by Anwar von Sroka, here: http://www.mydarc.de/dl5dbm/20a_e.pdf

Read More

Stereo amplifier 3W 3W using ic BA5406

IC number is BA5406 IC stereo audio amplifier size 3 watt + 3 watt.The circuit is small and easy to create.Suitable for expanding the use of music in a private room.Or may be used in any trial.
When raising the power supply 12 volts to this circuit.Input the left and the right to access the input pin, to pin 5 and pin 8 of IC.The signal through the C1 and C2 are coupling signal.To prevent DC, to interfere in the circuit.Then the amplifier IC is not a return phase.Exit output, Pin 2 and Pin 11.And the output signal out of each channel, left and right through C9 and C10.Add to block DC and low frequency stability.Then went out to the speakers.The C7 and C8 are connected to pins 3 and pin 10 of IC, respectively.The pin 3 and pin 10 is pin Boot Strap will help to gain a better.The C5 and C6 are connected to pins 6 and Pin 7.A pin Filter, the C5 and C6 serve cut noise from the IC.

Read More